AXIOM Beta Firmware Version 2.0

1 Prepare Micro SD Card

Get a new Micro SD card (4GB is enough, bigger is fine as well, but the partitions are not yet automatically resized when a bigger SD card is detected).
Acquire the latest automatically built firmware image from: https://github.com/apertus-open-source-cinema/axiom-beta-firmware/releases - don't be alarmed by the name "Unstable Development Snapshot" it just means the firmware has been automatically built without human interaction.
Download, install and start Etcher: https://www.balena.io/etcher/
Flash the acquired image to a new Micro SD card with Etcher (we highly recommend not overwriting the Micro SD card you currently use in your AXIOM Beta).
After flashing put the Micro SD card into the AXIOM Beta Microzed SD card slot and power up the Beta.

This new firmware is still in development so expect issues and bugs.

If you find a new bug or have ideas for improvement please add it as github issue (please first check it has not been reported yet).

Sudo is required to change system/camera settings (like running the various scripts)
All camera related programs and scripts are now prefixed with axiom- (for example to run set_gain.sh use run axiom-set_gain.sh). They are now executable from anywhere.
kick_manual.sh was renamed to axiom-start.sh
halt_manual.sh was renamed to axiom-stop.sh
cmv_snap3 was renamed to axiom-snap
axiom-sequencer-start.sh starts the continuous image acquisition (HDMI output).
axiom-sequencer-stop.sh stops the continuous image acquisition (HDMI output).
- For example : ./cmv_snap3 -e 20ms -z is now done by typing sudo axiom-snap -e 20ms -z
Image build log is located in each image under: /var/build.log
Devicetree source can be found at /boot/devicetree.dts. To recompile it after any changes use dtc -O dtb -o /boot/devicetree.dtb /boot/devicetree.dts
To interrupt the autoboot from u-boot send Ctrl-C over serial quickly after a boot / reboot (try holding it down)
axiom-file-check.sh does an integrity check of /usr, /etc and /opt
Binaries are linked in: /usr/axiom/bin
Scripts are linked in: /usr/axiom/script
/opt/axiom-firmware contains scripts and binaries
Every AXIOM Beta currently has the same MAC address - a random one should be generated on the first boot, but this is not implemented yet.
Second Micro SD card slot is enabled by default.
Factory Calibration Routines have been forked for firmware 2.0: Factory_Calibration_(firmware_2.0)

FPGA bitstreams are located in /usr/lib/firmware and softlinked to from /opt/bitstreams/
*.bit files (from old firmware) need to be converted to *.bin files (for new firmware) with:/opt/axiom-firmware/makefiles/in_chroot/to_raw_bitstream.py -f input_file.bit output_file.bin and copied to /lib/firmware
make sure to load new bitstreams as root (sudo su) and not with sudo or use echo $BITSTREAM_NAME | sudo tee /sys/class/fpga_manager/fpga0/firmware

Further documentation:

run:

sudo axiom-halt.sh

Create a copy of axiom-start.sh with a new name eg. axiom-start30.sh

cp $(which axiom-start.sh) axiom-start30.sh

In it replace this line:

echo axiom-fpga-main.bin > /sys/class/fpga_manager/fpga0/firmware

by this line (choosing appropriate files: _30 for 25P/30p or _60 for 50p/60p modes):

echo cmv_hdmi3_dual_30.bin > /sys/class/fpga_manager/fpga0/firmware

copy /opt/bitstreams/cmv_hdmi3_dual_30.bin to /lib/firmware:

sudo cp /opt/bitstreams/cmv_hdmi3_dual_30.bin /lib/firmware

execute the new script:

sudo axiom-start30.sh