Difference between revisions of "AXIOM Beta/AXIOM Beta Software"

From apertus wiki
Jump to: navigation, search
Line 115: Line 115:
TBD
TBD


===Start the camera===
==Start the camera==


The init script is automatically run at startup:
The init script is automatically run at startup:
Line 121: Line 121:


This will initialize all systems and train the sensor communication.
This will initialize all systems and train the sensor communication.


==Capture an image==
==Capture an image==

Revision as of 11:18, 27 May 2016

BetaGettingStarted.jpg


Note: Some of the instructions we have prepared are written in a way they can also be followed by people without advanced technical knowledge. If you are more of a "techie", please keep this in mind and skip or ignore the steps or passages which deal with information you already know.

1 Getting Started

1.1 Prep your AXIOM Beta camera for use

  1. Use a micro-USB cable to connect the camera's MicroZed development board (USB UART) to a computer. The MicroZed board is the backmost, red PCB. (There is another micro-USB socket on the Power Board, but that is the JTAG Interface.)
  2. Connect the ethernet port on the MicroZed to an ethernet port on your computer. You might have to use an ethernet adapter on newer, smaller machines which come without a native ethernet port.
  3. Connect the AC adapter to the camera's Power Board. (The power cord plugs into an adapter that connects to the Power Board; to power the camera off at a later point, you need not disconnect the adapter from the board but can just unplug the cord from the adapter.)


BetaGuide.jpg


1.2 Prep your computer for use with your camera

To communicate with your AXIOM Beta camera, you will send it instructions via your computer's command line.

In case you have not worked with a shell (console, terminal) much or ever before, we have prepared detailed instructions to help you get you set up. The steps which need to be taken to prepare your machine sometimes differ between operating systems, so pick the ones that are applicable to you(r system).

Note that dollar signs $ placed in front of commands are not meant to be typed in but denote the command line prompt (a signal indicating the computer is ready for user input). It is used in documentation to differentiate between commands and output resulting from commands. The prompt might look different on your machine (e.g. an angled bracket >) and be preceded by your user name, computer name or the name of the directory which you are currently inside.

1.2.1 USB to UART drivers

For the USB connection to work, you will need drivers for bridging USB to UART (USB to serial). They can be downloaded from e.g. Silicon Labs' website – pick the software provided for your OS and install it.

1.2.2 Serial console

The tool we recommend for connecting to the AXIOM Beta camera via serial port with Mac OS X or Linux is minicom; for connections from Windows machines, we have used Putty.

/Mac OS X setup/
/Linux setup/

1.3 Serial connection (via USB)

While the AXIOM Beta can be connected to via USB UART (USB to serial), a serial connection is not the preferred way to communicate with the camera but rather in place for monitoring purposes.

However, a serial connection is needed to set up communication via ethernet/LAN (the better suited way to talk to the camera): as the Beta only allows for secure ethernet connections, you will have to connect to the camera via serial port first and copy over your SSH key.


Once the Beta is connected and powered on (and you installed the necessary drivers), it gets listed as a USB device in the /dev directory of your file system, e.g.
/dev/ttyUSB0 (on Linux)
or
/dev/cu.SLAB_USBtoUART
/dev/tty.SLAB_USBtoUART (on Mac).


You can use use a command such as:

$ ls -al /dev | grep -i usb

to list all USB devices currently connected to your machine.


1.3.1 Connecting using screen

To connect to the camera, use the command:

screen file_path 115200

e.g. (depending on your operating system):

screen /dev/ttyttyUSB0 115200
screen /dev/tty.SLAB_USBtoUART 115200

You might have to run the command with superuser rights, i.e.:

sudo screen /dev/ttyttyUSB0 115200


On successful connection, you will be prompted to enter user credentials needed for logging into the camera.
If your terminal remains blank, try pressing enter.

The default credentials are:

user: root
password: beta


1.3.2 Disconnect from the camera

To disconnect from the camera again, use:

exit

The result will be a logout message followed by a new login prompt. To suspend or quit your screen session (and return to your regular terminal window) use one of the following commands:

CTRL+a CTRL+z
CTRL+a CTRL+\

1.4 Ethernet connection (using SSH)

To access the AXIOM Beta via Ethernet – which is the preferred way to communicate with it and will also work remotely, from a machine which is not directly connected to the camera – authentication via SSH is required.

If you have never created SSH keys before or need a refresher in order to create a new pair, see the How-to below.

SSH keys How-to Mac/Linux

1.4.1 Get/set IP address

If your machine is running dhcpd (which you would have had to install, i.e. which is not the case by default), the AXIOM Beta will request an IP address from DHCP automatically as soon as it is connected to your machine via Ethernet cable.

Otherwise, you will have to set the Beta's IP address manually with the ifconfig command.

1.4.1.1 IP address check

While connected to the AXIOM Beta via USB, you can use the command:

$ ip a l

on the Beta to check whether it is currently assigned an IP address. Find the entry which begins with eth0 and check if it contains a line starting with inet followed by an IP address. If it does, this is the IP address the Beta can be reached at.

Example output with no IP address assigned:

TBD
1.4.1.2 Set IP address

If the IP address check is not successful – in that it does not produce an IP address you can connect to – you will have to set your Beta's IP address manually with the ifconfig command.

While connected to the Beta, you can do that like so:

$ ifconfig eth0 192.168.0.9/24 up

It does not really matter which IP address you choose as long as it is one allowed for private use (e.g. addresses in the 192.168.x.x range) and you make sure to use the /24 prefix.

If you now use $ ip a l (again) to check for the camera's IP address, you should see the address you assigned listed after inet, e.g.:

TBD

1.4.2 Establish a connection

TBD

2 Start the camera

The init script is automatically run at startup:

./kick.sh

This will initialize all systems and train the sensor communication.

3 Capture an image

write the image into file: snap.raw16 plus display it with imagemagick:

ssh root@*BETA-IP* "./cmv_snap3 -e 10ms" | tee snap.raw16 | display -size 4096x3072 -depth 16 gray:-

same for 12bit (more efficient, same data):

ssh root@*BETA-IP* "./cmv_snap3 -2 -e 10ms" | tee snap.raw12 | display -size 4096x3072 -depth 12 gray:-

4 Overlay Images

clear overlay

./mimg -a -o -P 0

enable overlay:

gen_reg 11 0x0104F000

disable overlay:

gen_reg 11 0x0004F000

5 Addititonal outputs

Display voltages and current flow:

./pac1720_info.sh

Output:

ZED_5V        	5.0781 V [2080] 	+29.0625 mV [2e8]   +968.75 mA
BETA_5V       	5.1172 V [20c0] 	+26.6016 mV [2a9]   +886.72 mA
HDN           	3.2422 V [14c0] 	 -0.0391 mV [fff]     -1.30 mA
PCIE_N_V      	3.2422 V [14c0] 	 -0.0391 mV [fff]     -1.30 mA
HDS           	3.2422 V [14c0] 	 +0.0000 mV [000]     +0.00 mA
PCIE_S_V      	3.2422 V [14c0] 	 -0.0391 mV [fff]     -1.30 mA
RFW_V         	3.2812 V [1500] 	 +0.2734 mV [007]     +9.11 mA
IOW_V         	3.2422 V [14c0] 	 +0.0000 mV [000]     +0.00 mA
RFE_V         	3.2812 V [1500] 	 +0.2344 mV [006]     +7.81 mA
IOE_V         	3.2812 V [1500] 	 +0.0781 mV [002]     +2.60 mA
VCCO_35       	2.5000 V [1000] 	 +0.6641 mV [011]    +22.14 mA
VCCO_13       	2.4609 V [ fc0] 	 +1.2500 mV [020]    +41.67 mA
PCIE_IO       	2.4609 V [ fc0] 	 -0.0391 mV [fff]     -1.30 mA
VCCO_34       	2.4609 V [ fc0] 	 +0.8203 mV [015]    +27.34 mA
W_VW          	1.9922 V [ cc0] 	 -0.0781 mV [ffe]     -2.60 mA
N_VW          	3.1641 V [1440] 	 +0.0000 mV [000]     +0.00 mA
N_VN          	1.8750 V [ c00] 	+15.4297 mV [18b]   +514.32 mA
N_VE          	3.1641 V [1440] 	 +0.0000 mV [000]     +0.00 mA
E_VE          	1.9922 V [ cc0] 	 -0.0391 mV [fff]     -1.30 mA
S_VE          	1.9531 V [ c80] 	 +0.0000 mV [000]     +0.00 mA
S_VS          	2.9297 V [12c0] 	 +0.3906 mV [00a]    +13.02 mA
S_VW          	1.9922 V [ cc0] 	 -0.1562 mV [ffc]     -5.21 mA

Read Temperature on Zynq:

./zynq_info.sh 

Output:

ZYNQ Temp     	49.9545 °C

6 HDMI Modes

cmv_hdmi3.bit is the FPGA bitstream loaded for the HDMI interface. We use symlinks to switch this file easily.

6.1 Enable 1080p60 Mode

rm -f cmv_hdmi3.bit
ln -s cmv_hdmi3_60.bit cmv_hdmi3.bit
sync
reboot now

6.2 Enable 1080p30 Mode

rm -f cmv_hdmi3.bit
ln -s cmv_hdmi3_30.bit cmv_hdmi3.bit
sync
reboot now

7 Tools

7.1 cmv_reg

Get and Set CMV12000 image sensor registers (CMV12000 sports 128x16 Bit registers).

Details are in the sensor datasheet: https://github.com/apertus-open-source-cinema/beta-hardware/tree/master/Datasheets


Examples:

Read register 115 (which contains the analog gain settings):

cmv_reg 115

Return value:

0x00

Means we are currently operating at analog gain x1 = unity gain


Set register 115 to gain x2:

cmv_reg 115 1

7.2 set_gain.sh

Set gain and related settings (ADC range and offsets).

./set_gain.sh 1 
./set_gain.sh 2
./set_gain.sh 3/3 # almost the same as gain 1
./set_gain.sh 3
./set_gain.sh 4

7.3 cmv_snap3

Capture and store image snapshots and sequences.

Example:

ssh root@cameraip "./cmv_snap3 -B0x08000000 -x -N8 -L1024 -2 -e 5ms" >/tmp/test.seq12
-B setzt die buffer base und ist im augenblick erforderlich
0x08000000 bedeutet 128MB, ich hab das linux auf 128MB zusammengepfercht, damit bleibt 1024MB-128MB fuer sequenzen
bitte beachten, es gibt kein sicherheitsnetz und keine plausibilitaetschecks, d.h. wenn du addressen erreichst oder spezifizierst wo das linux laeuft, dann ist vermutlich ein reset notwendig
-x bedeutet das erste frame zu skippen (optional), da mir aufgefallen ist, dass das erste frame nach einer pause anders aussieht
-N setzt die anzahl der frames die zu capturen sind (bitte wieder beachten, wenn du ueber 0x3FFFFFFF kommst, dann ueberschreibst du den linux bereich)
-L setzt die anzahl der zeilen (nur gerade werte, max 3072)
-2 stellt auf 12bit output (einziges format das ich getestet habe :)
-e setzt die exposure wie gehabt

To split one seq12 file into multiple individual files:

split -b <size> <file.seq12> <prefix>
<size> the amount of bytes of one image (4096 x number-of-lines x 12bit / 8bit)
<prefix> name
optionally add --additional-suffix=.raw12 for the proper extension
-d or --numeric-suffixes for numeric numbering of the split files

Example for 1024 lines (input file: test.seq12):

split -b 6291456 -d test.seq12 output --additional-suffix=.raw12

Example for 1080 lines (input file: test.seq12):

split -b 6635520 -d test.seq12 output --additional-suffix=.raw12


Use imagemagick to convert raw12 file into a color preview image:

cat test.raw12 | convert \( -size 4096x3072 -depth 12 gray:- \) \( -clone 0 -crop -1-1 \) \( -clone 0 -crop -1+0 \) \( -clone 0 -crop +0-1 \) -sample 2048x1536 \( -clone 2,3 -average \) -delete 2,3 -swap 0,1 +swap -combine test_color.png

Capture directly to DNG, without saving the raw12, in the camera:

./cmv_snap3 -2 -b -r -e 10ms | raw2dng snap.DNG

8 General Info

Stop HDMI live stream:

fil_reg 15 0

Start HDMI live stream:

fil_reg 15 0x01000100

8.1 Operating System

At this moment we were able to reuse an Arch Linux image for the Zedboard on the Microzed. To do so, some software such as the FSBL and uboot were added. More information can be found here: http://stefan.konink.de/contrib/apertus/ I will commit myself on the production of a screencast of the entire bootstrap proces from the Xilinx software to booting the MicroZed.

I would suggest running Arch Linux on the AXIOM Beta for development purposes. If we need to shrink it down that will be quite trivial. Obviously we can take the embedded approach from there, as long as we don't fall in the trap of libc implementations with broken threading.

8.2 Moving Image Raw Recording/Processing

Note: This only works with the experimental raw mode enabled on the AXIOM Beta 1080p60 (A+B Frames) and is only tested with the Atomos Shogun currently.

To measure the required compensations with a different recorder follow this guide: this guide

Postprocessing software to recover the raw information (DNG sequences) is on github: https://github.com/apertus-open-source-cinema/misc-tools-utilities/tree/master/raw-via-hdmi

required packages: ffmpeg build-essentials

Mac requirements for compiling: gcc4.9(via homebrew):

brew install homebrew/versions/gcc49

also install ffmpeg

To do all the raw processing in one single command (after ffmpeg codec copy processing):

./hdmi4k INPUT.MOV - | ./raw2dng --fixrnt --pgm --black=120 frame%05d.dng

8.2.1 hdmi4k

Converts a video file recorded in AXIOM raw to a PGM image sequence and applies the darkframe (needs to be created beforehand).

Currently clips must go through ffmpeg before hdmi4k can read them:

ffmpeg -i CLIP.MOV -c:v copy OUTPUT.MOV

To cut out a video between IN and OUT with ffmpeg but maintaing the original encoding data:

ffmpeg -i CLIP.MOV -ss IN_SECONDS -t DURATION_SECONDS -c:v copy OUTPUT.MOV
hdmi4k
HDMI RAW converter for Axiom BETA

Usage:
  ./hdmi4k clip.mov
  raw2dng frame*.pgm [options]

Calibration files:
  hdmi-darkframe-A.ppm, hdmi-darkframe-B.ppm:
  averaged dark frames from the HDMI recorder (even/odd frames)

Options:
-                   : Output PGM to stdout (can be piped to raw2dng)
--3x3               : Use 3x3 filters to recover detail (default 5x5)
--skip              : Toggle skipping one frame (try if A/B autodetection fails)
--swap              : Swap A and B frames inside a frame pair (encoding bug?)
--onlyA             : Use data from A frames only (for bad takes)
--onlyB             : Use data from B frames only (for bad takes)


8.2.2 raw2dng

Converts a PGM image sequence to a DNG sequence.

DNG converter for Apertus .raw12 files

Usage:
  ./raw2dng input.raw12 [input2.raw12] [options]
  cat input.raw12 | ./raw2dng output.dng [options]

Flat field correction:
 - each gain requires two reference images (N=1,2,3,4):
 - darkframe-xN.pgm will be subtracted (data is x8)
 - gainframe-xN.pgm will be multiplied (1.0 = 16384)
 - reference images are 16-bit PGM, in the current directory.

Options:
--black=%d          : Set black level (default: autodetect)
                      - negative values allowed
--white=%d          : Set white level (default: 4095)
                      - if too high, you may get pink highlights
                      - if too low, useful highlights may clip to white
--width=%d          : Set image width (default: 4096)
--height=%d         : Set image height
                      - default: autodetect from file size
                      - if input is stdin, default is 3072
--swap-lines        : Swap lines in the raw data
                      - workaround for an old Beta bug
--hdmi              : Assume the input is a memory dump
                      used for HDMI recording experiments
--lut               : Linearize sensor response with per-channel LUTs
                      - probably correct only for one single camera :)
--fixpn             : Fix pattern noise (slow)
--no-darkframe      : Disable dark frame (if darkframe.pgm is present)
--no-gainframe      : Disable gain frame (if gainframe.pgm is present)

Debug options:
--dump-regs         : Dump sensor registers from the metadata block (no output DNG)
--fixpn-dbg-denoised: Pattern noise: show denoised image
--fixpn-dbg-noise   : Pattern noise: show noise image (original - denoised)
--fixpn-dbg-mask    : Pattern noise: show masked areas (edges and highlights)
--fixpn-dbg-row     : Pattern noise: debug rows (default: columns)

Example:

./raw2dng --fixrnt --pgm --black=120 frame%05d.dng

8.2.3 EDL Parser

This script can take EDLs to reduce the raw conversion/processing to the essential frames that are actually used in an edit. This way a finished video edit can be converted to raw DNG sequences easily.

Requirements: ruby

puts "BEFORE EXECUTION, PLS FILL IN YOUR WORK DIRECTORY IN THE SCRIPT (path_to_workdir)"


puts "#!/bin/bash"
i=0
ffmpeg_cmd1 = "ffmpeg -i " 

tc_in = Array.new
tc_out = Array.new
clip = Array.new

file = ARGV.first
ff = File.open(file, "r")

ff.each_line do |line|
	clip << line.scan(/NAME:\s(.+)/)
	tc_in << line.scan(/(\d\d:\d\d:\d\d:\d\d).\d\d:\d\d:\d\d:\d\d.\d\d:\d\d:\d\d:\d\d.\d\d:\d\d:\d\d:\d\d/)
	tc_out << line.scan(/\s\s\s\d\d:\d\d:\d\d:\d\d\s(\d\d:\d\d:\d\d:\d\d)/)

end
c=0
clip.delete_at(0)
clip.each do |fuck|
	if clip[c].empty?
		tc_in[c] = []
		tc_out[c] = []
	end
	c=c+1
end

total_frames = 0
tc_in = tc_in.reject(&:empty?)
tc_out = tc_out.reject(&:empty?)
clip = clip.reject(&:empty?)
tc_in.each do |f|
tt_in = String.new
tt_out = String.new
	tt_in = tc_in[i].to_s.scan(/(\d\d)\D(\d\d)\D(\d\d)\D(\d\d)/)
	tt_out = tc_out[i].to_s.scan(/(\d\d)\D(\d\d)\D(\d\d)\D(\d\d)/)
	framecount = ((tt_out[0][0].to_i-tt_in[0][0].to_i)*60*60*60+(tt_out[0][1].to_i-tt_in[0][1].to_i)*60*60+(tt_out[0][2].to_i-tt_in[0][2].to_i)*60+(tt_out[0][3].to_i-tt_in[0][3].to_i))
	framecount = framecount + 20
	tt_in_ff = (tt_in[0][3].to_i*1000/60)
	frames_in = tt_in[0][0].to_i*60*60*60+tt_in[0][1].to_i*60*60+tt_in[0][2].to_i*60+tt_in[0][3].to_i
	frames_in = frames_in - 10
	new_tt_in = Array.new
	new_tt_in[0] = frames_in/60/60/60
	frames_in = frames_in - new_tt_in[0]*60*60*60
	new_tt_in[1] = frames_in/60/60
	frames_in = frames_in - new_tt_in[1]*60*60
	new_tt_in[2] = frames_in/60
	frames_in = frames_in - new_tt_in[2]*60
	new_tt_in[3] = frames_in
	frames_left = (tt_in[0][0].to_i*60*60*60+(tt_in[0][1].to_i)*60*60+(tt_in[0][2].to_i)*60+(tt_in[0][3].to_i))-10
	new_frames = Array.new
	new_frames[0] = frames_left/60/60/60
	frames_left = frames_left - new_frames[0]*60*60*60
	new_frames[1] = frames_left/60/60
	frames_left = frames_left - new_frames[1]*60*60
	new_frames[2] = frames_left/60
	frames_left = frames_left - new_frames[2]*60
	new_frames[3] = frames_left
	tt_in_ff_new = (new_frames[3]*1000/60)

	clip[i][0][0] = clip[i][0][0].chomp("\r")
	path_to_workdir = "'/Volumes/getztron2/April Fool 2016/V'"
	mkdir = "mkdir #{i}\n"
	puts mkdir
	ff_cmd_new = "ffmpeg -ss #{sprintf '%02d', new_frames[0]}:#{sprintf '%02d', new_frames[1]}:#{sprintf '%02d', new_frames[2]}.#{sprintf '%02d', tt_in_ff_new} -i #{path_to_workdir}/#{clip[i][0][0].to_s} -frames:v #{framecount} -c:v copy p.MOV -y"
	puts ff_cmd_new
	puts "./render.sh p.MOV&&\n"
	puts "mv frame*.DNG #{i}/"
	hdmi4k_cmd = "hdmi4k #{path_to_workdir}/frame*[0-9].ppm --ufraw-gamma --soft-film=1.5 --fixrnt --offset=500&&\n"

	ff_cmd2 = "ffmpeg -i #{path_to_workdir}/frame%04d-out.ppm -vcodec prores -profile:v 3 #{clip[i][0][0]}_#{i}_new.mov -y&&\n"
	puts "\n\n\n"
	i=i+1
	total_frames = total_frames + framecount
end

puts "#Total frame: count: #{total_frames}"

Pipe it to a Bash file to have a shell script.

Note from the programmer: This is really unsophisticated and messy. Feel free to alter and share improvements.

8.3 Userspace

Arch Linux comes with systemd, which has one advantage that the boot process is incredible fast. Standard tools such as sshd and dhcpcd have been preinstalled. We may need other tools such as ftp, webserver, etc.

  • ftp; I would suggest vsftpd here
  • webserver; I am able to modify cherokee with custom C code to directly talk to specific camera sections. Cherokee already powers the WiFi module of the GoPro.

One idea to store camera relevant parameters inside the camera and provide access from most programming languages is to use a database like http://en.wikipedia.org/wiki/Berkeley_DB