Line 27: Line 27:
  
 
See more reading and exploration of options at [[Zynq Development Boards]].
 
See more reading and exploration of options at [[Zynq Development Boards]].
 
 
 
----
 
 
  
  
Line 39: Line 34:
  
 
[https://wiki.apertus.org/index.php/File:AES-Z7MB-7Z020-SOM-G_MicroZed_Datasheet.pdf Datasheet]
 
[https://wiki.apertus.org/index.php/File:AES-Z7MB-7Z020-SOM-G_MicroZed_Datasheet.pdf Datasheet]
 
 
----
 
  
  
Line 50: Line 42:
 
Fonsoning FSY31S05M 30x30x10mm 5V 0.12A fan
 
Fonsoning FSY31S05M 30x30x10mm 5V 0.12A fan
  
 +
 +
==customizations for AXIOM Beta==
 +
 +
We remove D4 and D8 and replace D8 with a 0R shunt.
 +
We install a custom heatsink and matching fan.
  
 
----
 
----

Revision as of 18:00, 9 July 2019

MicroZed™ is a low-cost development board based on the Xilinx Zynq®-7000 All Programmable SoC. Its unique design allows it to be used as both a stand-alone evaluation board for basic SoC experimentation, or combined with a carrier card as an embeddable system-on-module (SOM). MicroZed contains two I/O headers that provide connection to two I/O banks on the programmable logic (PL) side of the Zynq®-7000 All Programmable SoC device. In stand-alone mode, these 100 PL I/O are inactive. When plugged into a carrier card, the I/O are accessible in a manner defined by the carrier card design.



Note: There is nothing which makes the Zynq specifically suited for high bandwidth or camera applications etc. What makes it special is the combination of a microcontroller (hardened arm cores) and FPGA fabric. For us, the main reason to go with the Zynq was the availability of the MicroZed for a reasonable price.

If we would have built our own 'MicroZed' equivalent (which we'll probably do one day) it probably wouldn't use a Zynq.

Power - The Microzed draws around 8-15W, from our experience, depending on what the FPGA/CPUs are doing.


Decision making: In case you're wondering why we use Xilinx FPGA, and about other small form factors like Microsemi Igloo - We wanted to find a reasonably priced FPGA development board which also has a small size for the Beta. This narrowed the available options down to boards like the MicroZed and the Parallela. Back then, it was a bonus that we already knew the ZYNQ from the Zedboard (as it had been used on the AXIOM Alpha - The prototype proof of concept for AXIOM Beta). But there is really no special reason for Xilinx, we also use the Lattice FPGAs on our boards for routing e.g. AXIOM Beta Main Board.


Licensing:

All FPGAs can be used with the 'free' licenses (WebLicense, etc), this was something we made sure of, otherwise it wouldn't be very suitable for FOSS/OSH projects.

Both the Nexys (Nexys 4 DDR has an Artix XC7A100T in CSG324 which is covered by the free Web License) and the Zedboard also covered by the WebLicense. You won't get special Xilinx IP for free though.


See more reading and exploration of options at Zynq Development Boards.


1 Documentation, Schematics, BOM, etc.

http://zedboard.org/support/documentation/1519

Datasheet


2 Cooling

Custom CNC milled heatsink: https://github.com/apertus-open-source-cinema/beta-hardware/tree/master/Microzed-Heatsink

Fonsoning FSY31S05M 30x30x10mm 5V 0.12A fan


3 customizations for AXIOM Beta

We remove D4 and D8 and replace D8 with a 0R shunt. We install a custom heatsink and matching fan.