AXIOM Beta/AXIOM Beta Software

From apertus wiki
Jump to: navigation, search
BetaGettingStarted.jpg


Note: Some of the instructions we have prepared are written in a way they can also be followed by people without advanced technical knowledge. If you are more of a "techie", please keep this in mind and skip or ignore the steps or passages which deal with information you already know.

1 Getting Started

1.1 Prep your AXIOM Beta camera for use

  1. Use a micro-USB cable to connect the camera's MicroZed development board (USB UART) to a computer. The MicroZed board is the backmost, red PCB. (There is another micro-USB socket on the Power Board, but that is the JTAG Interface.)
  2. Connect the ethernet port on the MicroZed to an ethernet port on your computer. You might have to use an ethernet adapter on newer, smaller machines which come without a native ethernet port.
  3. Connect the AC adapter to the camera's Power Board. (The power cord plugs into an adapter that connects to the Power Board; to power the camera off at a later point, you need not disconnect the adapter from the board but can just unplug the cord from the adapter.)


BetaGuide.jpg


1.2 Prep your computer for use with your camera

To communicate with your AXIOM Beta camera, you will send it instructions via your computer's command line.

In case you have not worked with a shell (console, terminal) much or ever before, we have prepared detailed instructions to help you get you set up. The steps which need to be taken to prepare your machine sometimes differ between operating systems, so pick the ones that are applicable to you(r system).

Note that dollar signs $ placed in front of commands are not meant to be typed in but denote the command line prompt (a signal indicating the computer is ready for user input). It is used in documentation to differentiate between commands and output resulting from commands. The prompt might look different on your machine (e.g. an angled bracket >) and be preceded by your user name, computer name or the name of the directory which you are currently inside.

1.2.1 USB to UART drivers

For the USB connection to work, you will need drivers for bridging USB to UART (USB to serial). (Under Linux this works out of the box in most distributions) for other operating systems they can be downloaded from e.g. Silicon Labs' website – pick the software provided for your OS and install it.

1.2.2 Serial console

The tool we recommend for connecting to the AXIOM Beta camera via serial port with Mac OS X or Linux is minicom; for connections from Windows machines, we have used Putty.

/Mac OS X setup/
/Linux setup/

/minicom configuration/ instructions (Mac and Linux)

1.3 Serial connection (via USB)

While the AXIOM Beta can be connected to via USB UART (USB to serial), a serial connection is not the preferred way to communicate with the camera but rather in place for monitoring purposes.

However, a serial connection is needed to set up communication via ethernet/LAN (the better suited way to talk to the camera): as the Beta only allows for secure ethernet connections, you will have to connect to the camera via serial port first and copy over your SSH key.

Below are two different methods for connecting to the AXIOM Beta camera, using a program called minicom and an alternative program called screen. We suggest you try them in the order below, so if you can connect with minicom great, if not try screen.

1.3.1 Connect using minicom

Note that you will not be able to use the terminal window you initiate the serial connection in for anything else (it needs to remain open while you access the camera), so it might make sense to open a separate window just for this purpose.

With minicom installed and properly configured, all you need to do is run the following command to start it with the correct settings:

$ minicom -8 USB0

On successful connection, you will be prompted to enter user credentials (which are needed to log into the camera).

If your terminal remains blank except for the minicom welcome screen/information about your connection settings, try pressing enter. If this still does not result in the prompt for user credentials – while testing, we discovered the initial connection with minicom does not always work – disconnect the camera from the power adapter, then reconnect it: in your minicom window you should now see the camera's operating system booting up, followed by the login prompt. (From then on, connecting with minicom should work smoothly and at most require you to press enter to make the login prompt appear.)


The default credentials are:

user: root
password: beta

1.3.2 Alternative tools for serial connection

Before you can use any tool to initiate a serial connection with your Beta camera, you need to know through which special device file it can be accessed.

Once the Beta is connected and powered on (and you installed the necessary drivers), it gets listed as a USB device in the /dev directory of your file system, e.g.
/dev/ttyUSB0 (on Linux)
or
/dev/cu.SLAB_USBtoUART
/dev/tty.SLAB_USBtoUART (on Mac).

You can use a command such as:

$ ls -al /dev | grep -i usb

to list all USB devices currently connected to your machine.

1.3.2.1 screen

To connect to the camera, use the command:

$ screen file_path 115200

where file_path is the full path to the special device file (e.g. /dev/ttyUSB0 or /dev/cu.SLAB_USBtoUART).

You might have to run the command with superuser rights, i.e.:

$ sudo screen file_path 115200

On successful connection, you will be prompted to enter user credentials needed for logging into the camera.
If your terminal remains blank, try pressing enter.

The default credentials are:

user: root
password: beta

1.3.3 Disconnect

To exit the camera's operating system, use:

$ exit

The result will be a logout message followed by a new login prompt.

To suspend or quit your screen session (and return to your regular terminal window) use one of the following commands:

CTRL+a CTRL+z
CTRL+a CTRL+\

1.4 Ethernet connection (using SSH)

To access the AXIOM Beta via Ethernet – which is the preferred way to communicate with it and will also work remotely, from a machine which is not directly connected to the camera – authentication via SSH is required.

If you have never created SSH keys before or need a refresher in order to create a new pair, see the How-to below.

SSH keys How-to Mac/Linux

1.4.1 Get/set IP address

If your network has a DHCP server running somewhere (eg. router) the AXIOM Beta will receive an IP address automatically as soon as it is connected the network.

Otherwise, you will have to set the Beta's IP address manually with the ifconfig command over the serial console (USB).

1.4.1.1 IP address check

While connected to the AXIOM Beta via USB, you can use the command:

$ ip a l

on the Beta to check whether it is currently assigned an IP address. Find the entry which begins with eth0 and check if it contains a line starting with inet followed by an IP address. If it does, this is the IP address the Beta can be reached at.

Example output with no IP address assigned:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:0a:35:00:01:26 brd ff:ff:ff:ff:ff:ff
    inet6 fe80::20a:35ff:fe00:126/64 scope link 
       valid_lft forever preferred_lft forever
1.4.1.2 Set IP address

If the IP address check is not successful – in that it does not produce an IP address you can connect to – you will have to set your Beta's IP address manually with the ifconfig command.

While connected to the Beta, you can do that like so:

$ ifconfig eth0 192.168.0.9/24 up

It does not really matter which IP address you choose as long as it is one allowed for private use (e.g. addresses in the 192.168.x.x range) and you make sure to use the /24 prefix. Note that this will set the IP only until you reboot the camera - then the IP has to be set this same way. A more permanenty solution is using a router and connecting your camera and computer. Then the router assigns IPs using DHCP automatically.

If you now use $ ip a l (again) to check for the camera's IP address, you should see the address you assigned listed after inet, e.g.:

1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default 
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host 
       valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
    link/ether 00:0a:35:00:01:26 brd ff:ff:ff:ff:ff:ff
    inet 192.168.0.9/24 brd 192.168.0.255 scope global dynamic eth0
       valid_lft 172739sec preferred_lft 172739sec
    inet6 fe80::20a:35ff:fe00:126/64 scope link 
       valid_lft forever preferred_lft forever

1.4.2 Establish a connection via Key

Now we have the network configured we need to copy over our SSH key to the Beta.

While connected to the AXIOM Beta via USB, you can use the command:

cd ~/.ssh/
cp authorized_keys authorized_keys.orig

Strictly speaking the cp (copy) command isn't needed, but it's best practice to always make a copy of a file before editing it - just in case.

The next command will be to add your SSH key to the SSH file which contains the information on who can log into it via SSH without a password.

You will need to first copy (control/command c) - IMPORTANT, make sure that you copy the whole key but do not include the next/new line.

Next, with the command below, you will add your key to the authorized_keys file. The structure of the command below is:

  • echo - writes the text after it
  • [your key] - pastes (control/command v) your key, so do not type in [your key]!
  • > - overwrites the existing file and adds just this text
  • authorized_keys - make sure to spell this correctly.

As a heads-up when you paste in your SSH key the terminal window may wrap the text in a way that it looks like a bit of a mess - this is normal and you can then carry on typing in the rest of the command.

echo [yourkey] >> authorized_keys

Alternatively, you can use ssh-copy-id to do it. Don't forget to adapt the IP adress.

ssh-copy-id root@192.168.0.9

Now you have added you key you can then try and ssh into the Beta.

On your computer use the following command - note the IP address will be the one you set earlier, the one used below is just the example IP.

ssh root@192.168.0.9

You should now see the following prompt if you have logged on successfully to the Beta.

Last login: Fri Jun 10 15:12:17 2016
sourcing .bashrc ...
[root@beta ~]# 

Congratulations, you have now set up the Beta's networking and SSH configuration.

The minicom or screen method you used to connect is no longer needed.

1.4.2.1 Password Based Authentication

If you do not want to use the public/private keypair authentication you can edit /etc/ssh/sshd_config and set

PasswordAuthentication yes

Please note though that this can be a security vulnerability (especially if you do not change the default credentials) and connect your Beta directly to the Internet.

2 Start the camera

As development of the Beta continues the camera will initialize all systems and train the sensor communication automatically when powered on, but for now you will have to manually start this yourself.

Run the following command:

./kick_manual.sh

You will see a lot of output, the tail of it is below.

..
mapped 0x8030C000+0x00004000 to 0x8030C000.
mapped 0x80000000+0x00400000 to 0xA6961000.
mapped 0x18000000+0x08000000 to 0x18000000.
read buffer = 0x18390200
selecting RFW [bus A] ...
found MXO2-1200HC [00000001001010111010000001000011]
[root@beta ~]# 

If you look at the back of the camera you will now see a blue LED near the top flashing very fast - this indicates everything is now running.

If you turn the camera off when you turn it back on you will need to re-run this command.

3 Capture an image

For writing uncompressed full resolution full bitdepth raw image the AXIOM Beta uses a software called cmv_snap3.

It is located in the /root/ directory and writes the images data directly to STDOUT.

cmv_snap3 writes images in the RAW12 format. Writing one image takes a few seconds depending on where the image is written to so this method is not viable for recording video footage other than timelapse.

3.1 Documentation

The following parameters are available:

./cmv_snap3 -h
This is ./cmv_snap3 V1.10
options are:
-h        print this help message
-8        output 8 bit per pixel
-2        output 12 bit per pixel
-d        dump buffer memory
-b        enable black columns
-p        prime buffer memory
-r        dump sensor registers
-t        enable cmv test pattern
-z        produce no data output
-e <exp>  exposure times
-v <exp>  exposure voltages
-s <num>  shift values by <num>
-S <val>  writer byte strobe
-R <fil>  load sensor registers

3.2 Examples

Images can be written directly to the cameras internal micro SD card like this (10 milliseconds exposure time, 16bit):

./cmv_snap3 -e 10ms > image.raw16

Write image plus metadata (sensor configuration) to cameras internal micro SD card (20 milliseconds exposure time, 12bit):

./cmv_snap3 -2 -r -e 20ms > image.raw12

You can also use cmv_snap3 to change to exposure time (to 5 milliseconds in this example) without actually capturing an image, for the that -z parameter is used to not produce any data output:

./cmv_snap3 -z -e 5ms


That cmv_snap3 writes data to STDOUT makes it very versatile, we can for example capture images from and to a remote Linux machine connected to the Beta via Ethernet easily (lets assume the AXIOM Betas camera IP is set up as: 192.168.0.9 - SSH access has to be set up for this to work with a keypair)

ssh root@192.168.0.9 "./cmv_snap3 -2 -r -e 10ms" > snap.raw12

To pipe the data into a file and display it at the same time with imagemagick on a remote machine:

ssh root@192.168.0.9 "./cmv_snap3 -2 -r -e 10ms" | tee snap.raw12 | display -size 4096x3072 -depth 12 gray:-

Use imagemagick to convert raw12 file into a color preview image:

cat test.raw12 | convert \( -size 4096x3072 -depth 12 gray:- \) \( -clone 0 -crop -1-1 \) \( -clone 0 -crop -1+0 \) \( -clone 0 -crop +0-1 \) -sample 2048x1536 \( -clone 2,3 -average \) -delete 2,3 -swap 0,1 +swap -combine test_color.png

With raw2dng compiled inside the camera you can capture images directly to DNG, without saving the raw12:

./cmv_snap3 -2 -b -r -e 10ms | raw2dng snap.DNG

Note: Supplying exposure time as parameter is required otherwise cmv_snap3 will not capture an image. The exposure time can be supplied in "s" (seconds), "ms" (milliseconds), "us" (microseconds) and "ns" (nanoseconds). Decimal values also work (eg. "15.5ms").

4 Overlay Images

This section covers the mimg version 1.8 (see https://github.com/apertus-open-source-cinema/beta-software/tree/master/mimg), not the previous 1.6.

AXIOM Beta features a full HD framebuffer that can be altered from the Linux userspace and is automatically "mixed" with the real time video from the image sensor.

The overlay could also be used to draw live histograms/scopes/HUD or menus.

The overlay in more recent firmware revisions supports alpha channel transparency.

4.1 Prepare Overlay Images

Convert 24bit PNG (1920x1080 pixels) with transparency to AXIOM Beta raw format:

convert input.png rgba:output.rgb

Note that this image format is different as RAW12

4.2 mimg

mimg is the software running on the camera used to load/alter anything related to overlays or test images.

Source Code:

https://github.com/apertus-open-source-cinema/beta-software/tree/master/mimg

This is ./mimg V1.8
options are:
-h        print this help message
-a        load all buffers
-o        load as overlay
-O        load as color overlay
-r        load raw data
-w        use word sized data
-D <val>  image color depth
-W <val>  image width
-H <val>  image height
-P <val>  uniform pixel color
-T <val>  load test pattern
-B <val>  memory mapping base
-S <val>  memory mapping size
-A <val>  memory mapping address

4.3 Examples

clear overlay:

./mimg -a -o -P 0


load monochrome overlay:

./mimg -o -a file.raw


load color overlay:

./mimg -O -a file.raw


enable overlay:

gen_reg 11 0x0104F000


disable overlay:

gen_reg 11 0x0004F000

4.4 Old overlays

Overlays for mimg 1.6 are not compatible anymore. You can use

convert -size 1920x1080 -depth 6 rgba:overlay_04.rgb overlay_04.png

To convert them to PNG before continuing with the preparation above.

5 Misc Scripts

Display voltages and current flow:

./pac1720_info.sh

Output:

ZED_5V        	5.0781 V [2080] 	+29.0625 mV [2e8]   +968.75 mA
BETA_5V       	5.1172 V [20c0] 	+26.6016 mV [2a9]   +886.72 mA
HDN           	3.2422 V [14c0] 	 -0.0391 mV [fff]     -1.30 mA
PCIE_N_V      	3.2422 V [14c0] 	 -0.0391 mV [fff]     -1.30 mA
HDS           	3.2422 V [14c0] 	 +0.0000 mV [000]     +0.00 mA
PCIE_S_V      	3.2422 V [14c0] 	 -0.0391 mV [fff]     -1.30 mA
RFW_V         	3.2812 V [1500] 	 +0.2734 mV [007]     +9.11 mA
IOW_V         	3.2422 V [14c0] 	 +0.0000 mV [000]     +0.00 mA
RFE_V         	3.2812 V [1500] 	 +0.2344 mV [006]     +7.81 mA
IOE_V         	3.2812 V [1500] 	 +0.0781 mV [002]     +2.60 mA
VCCO_35       	2.5000 V [1000] 	 +0.6641 mV [011]    +22.14 mA
VCCO_13       	2.4609 V [ fc0] 	 +1.2500 mV [020]    +41.67 mA
PCIE_IO       	2.4609 V [ fc0] 	 -0.0391 mV [fff]     -1.30 mA
VCCO_34       	2.4609 V [ fc0] 	 +0.8203 mV [015]    +27.34 mA
W_VW          	1.9922 V [ cc0] 	 -0.0781 mV [ffe]     -2.60 mA
N_VW          	3.1641 V [1440] 	 +0.0000 mV [000]     +0.00 mA
N_VN          	1.8750 V [ c00] 	+15.4297 mV [18b]   +514.32 mA
N_VE          	3.1641 V [1440] 	 +0.0000 mV [000]     +0.00 mA
E_VE          	1.9922 V [ cc0] 	 -0.0391 mV [fff]     -1.30 mA
S_VE          	1.9531 V [ c80] 	 +0.0000 mV [000]     +0.00 mA
S_VS          	2.9297 V [12c0] 	 +0.3906 mV [00a]    +13.02 mA
S_VW          	1.9922 V [ cc0] 	 -0.1562 mV [ffc]     -5.21 mA

Read Temperature on Zynq:

./zynq_info.sh 

Output:

ZYNQ Temp     	49.9545 °C

6 HDMI Output

HDMI is a two-way communication protocol and supports a ton of different formats/frequencies/specs. Many monitors/recorders only support a subset of these formats and expect signals to conform to certain values. These values are not documented publicly so we are currently in the process of debugging device compatibility one by one. The good thing is that its a pure software thing and we can add support and test compatibility with additional devices as we go.

Watch this 33C3 talk by Tim Ansell about "Discecting HDMI": https://media.ccc.de/v/33c3-8057-dissecting_hdmi to get insight into how HDMI works.

Settings for VSync, HSync, etc. inside the AXIOM Beta can be found in:

/root/gen_init.sh

The Atomos SHOGUN was found to work with these parameters:

scn_reg  0 2200             # total_w
scn_reg  1 1125             # total_h
scn_reg  2   60             # total_f

scn_reg  4  262             # hdisp_s
scn_reg  5 2182             # hdisp_e
scn_reg  6   45             # vdisp_s
scn_reg  7 1125             # vdisp_e

scn_reg  8    0             # hsync_s
scn_reg  9 2100             # hsync_e
scn_reg 10    4             # vsync_s
scn_reg 11    9             # vsync_e

scn_reg 32  252             # pream_s
scn_reg 33  260             # guard_s
scn_reg 34  294             # terc4_e
scn_reg 35  296             # guard_e

Currently it is not possible to alter TMDS and Clock frequencies from the userspace (requires new FPGA bitstream).

For the firmware there are two modes available, the 30Hz and 60Hz variant. You can switch between them quite easily.

cmv_hdmi3.bit is the FPGA bitstream loaded for the HDMI interface. We use symlinks to switch this file easily.

Before doing this, don't forget to check if the files (cmv_hdmi3_60.bit or cmv_hdmi3_30.bit) really exist in the /root folder.

The output is always in 8bpc RGB color space without subsampling (4:4:4). Not all capture devices can manage this.

Other modes like YCrCb, etc. are currently not supported.

6.1 Enable 1080p60 Mode

rm -f cmv_hdmi3.bit
ln -s cmv_hdmi3_60.bit cmv_hdmi3.bit
sync
reboot now

6.2 Enable 1080p30 Mode

rm -f cmv_hdmi3.bit
ln -s cmv_hdmi3_30.bit cmv_hdmi3.bit
sync
reboot now

6.3 Generator and HDMI Output

Independet of the firmware you can switch the rate of the generator. In setup.sh you can change the generator resolution and framerate.

After changing the generator mode, make sure to restart it:

./halt_manual.sh && ./kick_manual.sh
./gen_init.sh 1080p60
./gen_init.sh 1080p50
./gen_init.sh 1080p25

To enable the shogun mode, which is only possibly by current hardware:

./gen_init.sh SHOGUN

In Shogun mode, the exposure (shutter) is synced to the output frame rate, but can be a multiple, i.e. with 60FPS output, it can be 60, 30, 20, 15, 12, ... The exposure time (shutter angle if divided by FPS) is entirely controlled by the sensor at the moment.

Note that the firmware controls the shutter, not the generator.

In the future, this will be combined and processed by only one piece of software.

7 Image Processing Pipeline

Draft pipeline taken from AXIOM Alpha for now.


Image Acquisition Pipeline:

Image04.png


HDMI Image Processing Pipeline:

Image01.png

7.1 Image Processing Nodes

7.1.1 Debayering

A planned feature is to generate this FPGA code block with "dynamic reconfiguration" meaning that the actual debayering algorithm can be replaced at any time by loading a new FPGA binary block at run-time. This tries to simplify creating custom debayering algorithms with a script like programming language that can be translated to FPGA code and loaded into the FPGA dynamically for testing.

7.1.2 Peaking Proposal

Peaking marks high image frequency areas with colored dot overlays. These marked areas are typically the ones "in-focus" currently so this is a handy tool to see where the focus lies with screens that have lower resolution than the camera is capturing.

Handy Custom Parameters:

  • color
  • frequency threshold

Potential Problems:

  • there are sharper and softer lenses so the threshold depends on the glass currently used. For a sharp lens the peaking could show areas as "in-focus" if they actually aren't and for softer lenses the peaking might never show up at all because the threshold is never reached

7.1.3 Image Blow Up / Zoom Proposal

Digital zoom into the center area of the image to check focus.

As extra feature this zoomed area could be moved around the full sensor area.

20140909152450-look-around.jpg


This feature is also related to the "Look Around" where the viewfinder sees a larger image area than is being output to the clean-feed.

This re-sampling method to scale up/down an image in real-time can be of rather low quality (nearest neighbor/bilinear/etc.) as it is only for preview purposes.


8 Tools

8.1 cmv_reg

Get and Set CMV12000 image sensor registers (CMV12000 sports 128x16 Bit registers).

Details are in the sensor datasheet: https://github.com/apertus-open-source-cinema/beta-hardware/tree/master/Datasheets


Examples:

Read register 115 (which contains the analog gain settings):

cmv_reg 115

Return value:

0x00

Means we are currently operating at analog gain x1 = unity gain


Set register 115 to gain x2:

cmv_reg 115 1

8.2 set_gain.sh

Set gain and related settings (ADC range and offsets).

./set_gain.sh 1 
./set_gain.sh 2
./set_gain.sh 3/3 # almost the same as gain 1
./set_gain.sh 3
./set_gain.sh 4


8.3 gamma_conf.sh

Set the gamma value:

./gamma_conf 0.4
./gamma_conf 0.9
./gamma_conf 1
./gamma_conf 2

8.4 Setting Exposure Time

To set the exposure time use the cmv_snap3 tool with -z parameter (this will tell the software to not save the image):

./cmv_snap3 -e 9.2ms -z

Note: The exposure time can be supplied in "s" (seconds), "ms" (milliseconds), "us" (microseconds) and "ns" (nanoseconds). Decimal values also work (eg. "15.5ms").


8.5 mat4_conf.sh

Read the details about the Matrix Color Conversion math/implementation.

To set the 4x4 color conversion matrix, you can use the mat4_conf.sh script:

The default configuration:

./mat4_conf.sh  1 0 0 0  0 1 0 0  0 0 1 0  0 0 0 1  0 0 0 0 

Please note that in current AXIOM Beta firmware the mat4 order is changed and the default matrix is:

./mat4_conf.sh 0.3 0.3 0.3 0.3  0 0 0 1  0 0.42 0.42 0  1 0 0 0

This will be changed to reflect the documentation again soon.

This 4x4 conversion matrix is a very powerful tool and allows to do things like mixing color channels, reassigning channels, applying effects or doing white balancing.

TODO: order is blue, green, red!

Mat4-conf-illustration-01.jpg

8.5.1 4x4 Matrix Examples:

./mat4_conf.sh  1 0 0 0  0 1 0 0  0 0 1 0  0 0 0 1    0 0 0 0   # unity matrix but not optimal as both green channels are processed separately
./mat4_conf.sh  1 0 0 0  0 0.5 0.5 0  0 0.5 0.5 0  0 0 0 1    0 0 0 0   # the two green channels inside each 2x2 pixel block are averaged and output on both green pixels
./mat4_conf.sh  0 0 0 1  0 1 0 0  0 0 1 0  1 0 0 0    0 0 0 0   # red and blue are swapped
./mat4_conf.sh  1 0 0 0  0 1 0 0  0 0 1 0  0 0 0 1    0.5 0 0 0    # red 50% brigther
./mat4_conf.sh  1 0 0 0  0 1 0 0  0 0 1 0  0 0 0 1.5    0 0 0 0    # blue multiplied with factor 1.5
./mat4_conf.sh  .25 .25 .25 .25  .25 .25 .25 .25  .25 .25 .25 .25  .25 .25 .25 .25    0 0 0 0    # black/white
./mat4_conf.sh  -1 0 0 0  0 -0.5 -0.5 0  0 -0.5 -0.5 0  0 0 0 -1    1 1 1 1    # negative

8.6 Clipping

scn_reg 28 0x00 # deactivate clipping
scn_reg 28 0x10 # activate low clipping
scn_reg 28 0x20 # activate high clipping
scn_reg 28 0x30 # activate high+low clipping

9 General Info

Stop HDMI live stream:

fil_reg 15 0

Start HDMI live stream:

fil_reg 15 0x01000100

9.1 Operating System

At this moment we were able to reuse an Arch Linux image for the Zedboard on the Microzed. To do so, some software such as the FSBL and uboot were added. More information can be found here: http://stefan.konink.de/contrib/apertus/ I will commit myself on the production of a screencast of the entire bootstrap proces from the Xilinx software to booting the MicroZed.

I would suggest running Arch Linux on the AXIOM Beta for development purposes. If we need to shrink it down that will be quite trivial. Obviously we can take the embedded approach from there, as long as we don't fall in the trap of libc implementations with broken threading.

9.1.1 Packet Manager Pacman

Update all package definitions and the database from the Internet:

pacman -Sy

Careful with upgrading existing packages. For example the Kernel used in the AXIOM Beta is custom developed - if you upgrade Arch Linux to the latest off the shelf Kernel you will BRICK your camera.


Install lighttp webserver on the Beta:

pacman -S lighttpd

Install PHP on the Beta:

pacman -S php php-cgi

Follow these instructions: https://wiki.archlinux.org/index.php/lighttpd#PHP

Start the webserver:

systemctl start lighttpd

9.2 Moving Image Raw Recording/Processing

9.2.1 Enable Raw recording mode

Note: This experimental raw mode works only in 1080p60 (A+B Frames) and is only tested with the Atomos Shogun currently.

To measure the required compensations with a different recorder follow this guide: this guide

This mode requires darkframes which are created in the course of a camera Factory Calibration. Early Betas are not calibrated yet - this step needs to be completed by the user.

Enable raw recording mode:

./hdmi_rectest.sh

Inside that script the following command is worth noting:

Enable experimental raw mode:

scn_reg 31 0x0A01

Disable experimental raw mode:

scn_reg 31 0x0001


if you get an error report like this:

Traceback (most recent call last):
  File "rcn_darkframe.py", line 17, in <module>
    import png
ImportError: No module named 'png'

Make sure the Beta is connected to the Internet via Ethernet and run:

pip install pypng

9.2.2 Processing

Postprocessing software to recover the raw information (DNG sequences) is on github: https://github.com/apertus-open-source-cinema/misc-tools-utilities/tree/master/raw-via-hdmi

required packages: ffmpeg build-essentials

Mac requirements for compiling: gcc4.9(via homebrew):

brew install homebrew/versions/gcc49

also install ffmpeg

To do all the raw processing in one single command (after ffmpeg codec copy processing):

./hdmi4k INPUT.MOV - | ./raw2dng --fixrnt --pgm --black=120 frame%05d.dng

9.2.3 hdmi4k

Converts a video file recorded in AXIOM raw to a PGM image sequence and applies the darkframe (needs to be created beforehand).

Currently clips must go through ffmpeg before hdmi4k can read them:

ffmpeg -i CLIP.MOV -c:v copy OUTPUT.MOV

To cut out a video between IN and OUT with ffmpeg but maintaing the original encoding data:

ffmpeg -i CLIP.MOV -ss IN_SECONDS -t DURATION_SECONDS -c:v copy OUTPUT.MOV
hdmi4k
HDMI RAW converter for Axiom BETA

Usage:
  ./hdmi4k clip.mov
  raw2dng frame*.pgm [options]

Calibration files:
  hdmi-darkframe-A.ppm, hdmi-darkframe-B.ppm:
  averaged dark frames from the HDMI recorder (even/odd frames)

Options:
-                   : Output PGM to stdout (can be piped to raw2dng)
--3x3               : Use 3x3 filters to recover detail (default 5x5)
--skip              : Toggle skipping one frame (try if A/B autodetection fails)
--swap              : Swap A and B frames inside a frame pair (encoding bug?)
--onlyA             : Use data from A frames only (for bad takes)
--onlyB             : Use data from B frames only (for bad takes)


9.2.4 raw2dng

Converts AXIOM Beta raw image to DNG.

DNG converter for Apertus .raw12 files

Usage:
  ./raw2dng input.raw12 [input2.raw12] [options]
  cat input.raw12 | ./raw2dng output.dng [options]

Flat field correction:
 - for each gain (N=1,2,3,4), you may use the following reference images:
 - darkframe-xN.pgm will be subtracted (data is x8 + 1024)
 - dcnuframe-xN.pgm will be multiplied by exposure and subtracted (x8192 + 8192)
 - gainframe-xN.pgm will be multiplied (1.0 = 16384)
 - clipframe-xN.pgm will be subtracted from highlights (x8)
 - reference images are 16-bit PGM, in the current directory
 - they are optional, but gain/clip frames require a dark frame
 - black ref columns will also be subtracted if you use a dark frame.

Creating reference images:
 - dark frames: average as many as practical, for each gain setting,
   with exposures ranging from around 1ms to 50ms:
        raw2dng --calc-darkframe *-gainx1-*.raw12 
 - DCNU (dark current nonuniformity) frames: similar to dark frames,
   just take a lot more images to get a good fit (use 256 as a starting point):
        raw2dng --calc-dcnuframe *-gainx1-*.raw12 
   (note: the above will compute BOTH a dark frame and a dark current frame)
 - gain frames: average as many as practical, for each gain setting,
   with a normally exposed blank OOF wall as target, or without lens
   (currently used for pattern noise reduction only):
        raw2dng --calc-gainframe *-gainx1-*.raw12 
 - clip frames: average as many as practical, for each gain setting,
   with a REALLY overexposed blank out-of-focus wall as target:
        raw2dng --calc-clipframe *-gainx1-*.raw12 
 - Always compute these frames in the order listed here
   (dark/dcnu frames, then gain frames (optional), then clip frames (optional).

General options:
--black=%d          : Set black level (default: 128)
                      - negative values allowed
--white=%d          : Set white level (default: 4095)
                      - if too high, you may get pink highlights
                      - if too low, useful highlights may clip to white
--width=%d          : Set image width (default: 4096)
--height=%d         : Set image height
                      - default: autodetect from file size
                      - if input is stdin, default is 3072
--swap-lines        : Swap lines in the raw data
                      - workaround for an old Beta bug
--hdmi              : Assume the input is a memory dump
                      used for HDMI recording experiments
--pgm               : Expect 16-bit PGM input from stdin

--lut               : Use a 1D LUT (lut-xN.spi1d, N=gain, OCIO-like)

--totally-raw       : Copy the raw data without any manipulation
                      - metadata and pixel reordering are allowed.

Pattern noise correction:
--rnfilter=1        : FIR filter for row noise correction from black columns
--rnfilter=2        : FIR filter for row noise correction from black columns
                      and per-row median differences in green channels
--fixrn             : Fix row noise by image filtering (slow, guesswork)
--fixpn             : Fix row and column noise (SLOW, guesswork)
--fixrnt            : Temporal row noise fix (use with static backgrounds; recommended)
--fixpnt            : Temporal row/column noise fix (use with static backgrounds)
--no-blackcol-rn    : Disable row noise correction from black columns
                      (they are still used to correct static offsets)
--no-blackcol-ff    : Disable fixed frequency correction in black columns

Flat field correction:
--dchp              : Measure hot pixels to scale dark current frame
--no-darkframe      : Disable dark frame (if darkframe-xN.pgm is present)
--no-dcnuframe      : Disable dark current frame (if dcnuframe-xN.pgm is present)
--no-gainframe      : Disable gain frame (if gainframe-xN.pgm is present)
--no-clipframe      : Disable clip frame (if clipframe-xN.pgm is present)
--no-blackcol       : Disable black reference column subtraction
                      - enabled by default if a dark frame is used
                      - reduces row noise and black level variations
--calc-darkframe    : Average a dark frame from all input files
--calc-dcnuframe    : Fit a dark frame (constant offset) and a dark current frame
                      (exposure-dependent offset) from files with different exposures
                      (starting point: 256 frames with exposures from 1 to 50 ms)
--calc-gainframe    : Average a gain frame (aka flat field frame)
--calc-clipframe    : Average a clip (overexposed) frame
--check-darkframe   : Check image quality indicators on a dark frame

Debug options:
--dump-regs         : Dump sensor registers from metadata block (no output DNG)
--fixpn-dbg-denoised: Pattern noise: show denoised image
--fixpn-dbg-noise   : Pattern noise: show noise image (original - denoised)
--fixpn-dbg-mask    : Pattern noise: show masked areas (edges and highlights)
--fixpn-dbg-col     : Pattern noise: debug columns (default: rows)
--export-rownoise   : Export row noise data to octave (rownoise_data.m)
--get-pixel:%d,%d   : Extract one pixel from all input files, at given coordinates,
                      and save it to pixel.csv, including metadata. Skips DNG output.


Example:

./raw2dng --fixrnt --pgm --black=120 frame%05d.dng

9.2.4.1 Compiling raw2dng

Compiling raw2dng on a 64bit system requires the gcc-multilib package

Ubuntu:

sudo apt-get install gcc-multilib

openSUSE:

sudo zypper install gcc-32bit libgomp1-32bit

AXIOM Beta:

  1. acquire the source from https://github.com/apertus-open-source-cinema/misc-tools-utilities/tree/master/raw2dng
  2. copy files to AXIOM Beta
  3. remove "-m32" from Makefile
  4. run "make" inside camera

9.2.5 EDL Parser

This script can take EDLs to reduce the raw conversion/processing to the essential frames that are actually used in an edit. This way a finished video edit can be converted to raw DNG sequences easily.

Requirements: ruby

puts "BEFORE EXECUTION, PLS FILL IN YOUR WORK DIRECTORY IN THE SCRIPT (path_to_workdir)"


puts "#!/bin/bash"
i=0
ffmpeg_cmd1 = "ffmpeg -i " 

tc_in = Array.new
tc_out = Array.new
clip = Array.new

file = ARGV.first
ff = File.open(file, "r")

ff.each_line do |line|
	clip << line.scan(/NAME:\s(.+)/)
	tc_in << line.scan(/(\d\d:\d\d:\d\d:\d\d).\d\d:\d\d:\d\d:\d\d.\d\d:\d\d:\d\d:\d\d.\d\d:\d\d:\d\d:\d\d/)
	tc_out << line.scan(/\s\s\s\d\d:\d\d:\d\d:\d\d\s(\d\d:\d\d:\d\d:\d\d)/)

end
c=0
clip.delete_at(0)
clip.each do |fuck|
	if clip[c].empty?
		tc_in[c] = []
		tc_out[c] = []
	end
	c=c+1
end

total_frames = 0
tc_in = tc_in.reject(&:empty?)
tc_out = tc_out.reject(&:empty?)
clip = clip.reject(&:empty?)
tc_in.each do |f|
tt_in = String.new
tt_out = String.new
	tt_in = tc_in[i].to_s.scan(/(\d\d)\D(\d\d)\D(\d\d)\D(\d\d)/)
	tt_out = tc_out[i].to_s.scan(/(\d\d)\D(\d\d)\D(\d\d)\D(\d\d)/)
	framecount = ((tt_out[0][0].to_i-tt_in[0][0].to_i)*60*60*60+(tt_out[0][1].to_i-tt_in[0][1].to_i)*60*60+(tt_out[0][2].to_i-tt_in[0][2].to_i)*60+(tt_out[0][3].to_i-tt_in[0][3].to_i))
	framecount = framecount + 20
	tt_in_ff = (tt_in[0][3].to_i*1000/60)
	frames_in = tt_in[0][0].to_i*60*60*60+tt_in[0][1].to_i*60*60+tt_in[0][2].to_i*60+tt_in[0][3].to_i
	frames_in = frames_in - 10
	new_tt_in = Array.new
	new_tt_in[0] = frames_in/60/60/60
	frames_in = frames_in - new_tt_in[0]*60*60*60
	new_tt_in[1] = frames_in/60/60
	frames_in = frames_in - new_tt_in[1]*60*60
	new_tt_in[2] = frames_in/60
	frames_in = frames_in - new_tt_in[2]*60
	new_tt_in[3] = frames_in
	frames_left = (tt_in[0][0].to_i*60*60*60+(tt_in[0][1].to_i)*60*60+(tt_in[0][2].to_i)*60+(tt_in[0][3].to_i))-10
	new_frames = Array.new
	new_frames[0] = frames_left/60/60/60
	frames_left = frames_left - new_frames[0]*60*60*60
	new_frames[1] = frames_left/60/60
	frames_left = frames_left - new_frames[1]*60*60
	new_frames[2] = frames_left/60
	frames_left = frames_left - new_frames[2]*60
	new_frames[3] = frames_left
	tt_in_ff_new = (new_frames[3]*1000/60)

	clip[i][0][0] = clip[i][0][0].chomp("\r")
	path_to_workdir = "'/Volumes/getztron2/April Fool 2016/V'"
	mkdir = "mkdir #{i}\n"
	puts mkdir
	ff_cmd_new = "ffmpeg -ss #{sprintf '%02d', new_frames[0]}:#{sprintf '%02d', new_frames[1]}:#{sprintf '%02d', new_frames[2]}.#{sprintf '%02d', tt_in_ff_new} -i #{path_to_workdir}/#{clip[i][0][0].to_s} -frames:v #{framecount} -c:v copy p.MOV -y"
	puts ff_cmd_new
	puts "./render.sh p.MOV&&\n"
	puts "mv frame*.DNG #{i}/"
	hdmi4k_cmd = "hdmi4k #{path_to_workdir}/frame*[0-9].ppm --ufraw-gamma --soft-film=1.5 --fixrnt --offset=500&&\n"

	ff_cmd2 = "ffmpeg -i #{path_to_workdir}/frame%04d-out.ppm -vcodec prores -profile:v 3 #{clip[i][0][0]}_#{i}_new.mov -y&&\n"
	puts "\n\n\n"
	i=i+1
	total_frames = total_frames + framecount
end

puts "#Total frame: count: #{total_frames}"

Pipe it to a Bash file to have a shell script.

Note from the programmer: This is really unsophisticated and messy. Feel free to alter and share improvements.

9.3 Userspace

Arch Linux comes with systemd, which has one advantage that the boot process is incredible fast. Standard tools such as sshd and dhcpcd have been preinstalled. We may need other tools such as ftp, webserver, etc.

  • ftp; I would suggest vsftpd here
  • webserver; I am able to modify cherokee with custom C code to directly talk to specific camera sections. Cherokee already powers the WiFi module of the GoPro.

One idea to store camera relevant parameters inside the camera and provide access from most programming languages is to use a database like http://en.wikipedia.org/wiki/Berkeley_DB

9.3.1 Firmware Backup

The entire camera firmware is stored on a Micro SD card plugged into the Microzed. To back up the entire firmware we plug in the Micro SD card into a Linux PC and do the following:

1. Find out which device the micro SD card is:

cat /proc/partitions
mount

should give you a list of all connected devices. Lets assume in our case that the card is /dev/sdc

2. Make sure the card is unmounted (all 3 partitions):

umount /dev/sdc1
umount /dev/sdc2
umount /dev/sdc3

3. clone the entire card to a file:

dd if=/dev/sdc of=sdimage.img bs=4M


Here is a guide that covers doing the same on Mac and Windows: http://raspberrypi.stackexchange.com/questions/311/how-do-i-backup-my-raspberry-pi

9.3.2 Firmware Restore

Again you need to know the device path of your sd card, then (assuming in our case its /dev/sdb) run:

sudo dd if=sdimage.img of=/dev/sdb bs=4M

10 Tutorials / Guides / Research

Installing a webserver on AXIOM Beta

AXIOM Beta as photography camera

Factory Calibration

Black Calibration

Pattern Noise

PLR

Sensor Cleaning

Firmware Image Creation