Difference between revisions of "Beta Main Board"

From apertus wiki
Jump to: navigation, search
Line 14: Line 14:




In the centre of the Main Board, and on both sides of the PCB, a 'solder-on' area for [[Beta CSO]]s has been incorporated. CSOs host sensor chips capable of, for example, sensing the camera's orientation and acceleration (the same chips used to stabilise quad-copters and track head movements in VR headsets). Being situated directly behind the image sensor's centre means that these sensors are ideally positioned to supply data surrounding image stabilisation or metadata about the camera’s orientation and movement during a shot.  
In the centre of the Main Board, and on both sides of the PCB, a 'solder-on' area for [[Beta CSO]]s has been incorporated. CSOs host sensor chips capable of, for example, sensing the camera's orientation and acceleration (the same chips used to stabilise quad-copters and track head movements in VR headsets). Being situated directly behind the image sensor's centre means that these sensors are ideally positioned to supply data surrounding image stabilisation or metadata about the camera’s orientation and movement during a shot. Two Lattice FPGAs (the so called routing fabrics) handle all the low speed GPIO communications that are required for plugin modules, shields and CSOs without sacrificing valuable Zynq GPIOs.


[[File:ABCS-MB-02b- AXIOM Beta Main Board V0.36R1.2 Bottom Populated sm02.jpg  | 1150px |]]
[[File:ABCS-MB-02b- AXIOM Beta Main Board V0.36R1.2 Bottom Populated sm02.jpg  | 1150px |]]


[https://wiki.apertus.org/images/1/14/ABCS-MB-02b-_AXIOM_Beta_Main_Board_V0.36R1.2_Bottom_Populated.jpg Full size image.]
[https://wiki.apertus.org/images/1/14/ABCS-MB-02b-_AXIOM_Beta_Main_Board_V0.36R1.2_Bottom_Populated.jpg Full size image.]






The Main Board is positioned between the Interface Board and the Power Board in the camera's PCB stack.
The Main Board is positioned between the Interface Board and the Power Board in the camera's PCB stack.
The purpose of the two Lattice FPGAs (the so called routing fabrics) is to handle all the low speed GPIO communications that are required for plugin modules, shields and CSOs without sacrificing valuable Zynq GPIOs.





Revision as of 14:11, 21 February 2019

00-MB-001- AXIOM Beta Main Board V0.36R1.2 Bottom Populated 02 Show sm b.jpg

Full size image.


The Beta Main Board is the camera's equivalent of a PC's motherboard. It hosts two external medium-speed shield connectors and two high-speed plugin module slot connectors - These act as a central switch for defining where the data that's captured by the sensor and other interfaces gets routed to inside the hardware. In this regard, all specifics can be dynamically reconfigured in software.


ABCS-MB-02a- AXIOM Beta Main Board V0.36R1.2 Top Populated sm 02.jpg

Full size image.


In the centre of the Main Board, and on both sides of the PCB, a 'solder-on' area for Beta CSOs has been incorporated. CSOs host sensor chips capable of, for example, sensing the camera's orientation and acceleration (the same chips used to stabilise quad-copters and track head movements in VR headsets). Being situated directly behind the image sensor's centre means that these sensors are ideally positioned to supply data surrounding image stabilisation or metadata about the camera’s orientation and movement during a shot. Two Lattice FPGAs (the so called routing fabrics) handle all the low speed GPIO communications that are required for plugin modules, shields and CSOs without sacrificing valuable Zynq GPIOs.

ABCS-MB-02b- AXIOM Beta Main Board V0.36R1.2 Bottom Populated sm02.jpg

Full size image.


The Main Board is positioned between the Interface Board and the Power Board in the camera's PCB stack.



1 Current Revision

AXIOM Beta Main Board V0.36 R1.2


2 Revision Archive

AXIOM Beta Main Board V0.35

AXIOM Beta Main Board V0.33

AXIOM Beta Main Board V0.29

AXIOM Beta Board 100 v0.16

axiom beta board 100 v0.15 test